Dana 60 Axle Parts
Front | Standard Rotation | High Carrier | 35 Spline Shafts
If this is not your axle, click here
The Dana 60 front low pinion axle with 4.56 and up carrier and 35 spline axle shafts is an extremely popular configuration and has been used by GM and Dodge since the 1970s. Dana 60 axles with 35 spline axles shafts are also often referred to as Dana 60HD ("heavy duty") axles. The parts listed on this page have been verified to fit this axle configuration.
- Front Dana 60HD (Full-Float)
Minor and Master Overhaul Kits
When servicing an axle or installing new gears or a new differential, it is a good idea to replace the internal seals, bearings, and any parts that get damaged during disassembly. These minor and master install kits include all of the high quality parts you need.
Learn More About Installation Kits
Ring and Pinion Gears
If you are changing tire size or want to improve the mileage or towing capability of your vehicle, then you'll want to change your axle's gear ratio. For help choosing the correct ratio, see the Crawlpedia Gear Ratio Guide
Note: The Dana 60 axle has a 4.10/4.56 carrier break. To run 4.30 and lower gears, you will need a 4.10 and down differential carrier. To learn more about carrier breaks, see Thick Gears and Carrier Breaks
To change to a 4.10 and down differential and run 4.30 and lower gears, you will need:
[ Dana 60 Low Carrier Differentials ] + [ Dana 60 Low Carrier Gears ]
Learn More About Ring and Pinion Gears
Differentials and Lockers
The best thing you can do to improve the traction of your vehicle is to install a differential locker or limited slip differential. For more information on each type of differential, click on the links below.
These differentials will work with the original gears in your axle as well as any of the gears listed in the section above. If you are changing your gear ratio, please see the gear section above first.
Learn More About Differential Lockers
Differential Locker Comparison
Replace your broken or worn out axle shafts with stock replacements or upgrade to high performance chrome-moly axle shafts to handle more power and larger tires.
Note: Dana 60 axles use various length axle shafts. You will need to either measure your existing shafts to order the proper length or order a set that can be cut to size. Quadrasteer axles are not supported at this time.
Learn More About Axle Shafts
Locking Hubs and Drive Flanges
Upgrade to heavy duty aftermarket locking hubs or convert to drive flanges for the ultimate in strength and reliability. A free-spin conversion kit is also available to reduce rolling resistance and increase fuel economy.
Note: Standard front 35 spline Dana 60 axles feature 30 spline stub shafts, however, 35 spline stub shafts are a very common upgrade.
Learn More About Hubs and Flanges
Stock Dana 60 knuckles are plenty strong for most application, however, if you are running tires over 40" tall with hydraulic steering, or if you simply run your vehicle extra hard, you will want forged steering knuckles.
Learn More About Steering Knuckles
If your spindles have been damaged or scarred by worn out bearings, it's time to upgrade to a set of heavy duty, heat treated, aftermarket spindles that are stronger and will last longer.
Learn More About Spindles
High Steer / Crossover Arms
Move your drag link, and tie rod up and out of the way while also making your steering knuckles stronger with a set of high steer arms. This upgrade is highly recommend for vehicles with large leaf spring lifts and those running hydraulic steering.
Learn More About Crossover Steering
Hydro Assist / Full Hydro Steering
Oversize tires take significantly more force to steer which can make steering a chore and may even cause your stock steering box to fail. Upgrade your steering system with a hydraulic assist cylinder or convert to full hydraulic steering with these kits.
Learn More About Hydraulic Steering
Beef up your Dana 60 axle housing with a precision cut and bent axle truss to handle larger tires and severe off-road abuse without flexing, bending, or breaking your axle.
Learn More About Axle Trusses
Tabs and Brackets
Converting to a 4-link suspension requires new shock mounts, link mounts, gussets, and tabs. Save yourself time, money and frustration with high quality, pre-fabricated, precision fit brackets.
Learn More About Axle Brackets and Tabs
Differential Covers and Guards
Protect your differential with a heavy duty differential cover or bring down your differential temperatures with a high capacity finned cover for maximum heat dissipation.
Learn More About Differential Covers
Differential Cover Gaskets
Red High-Temp RTV Silicone (available at your local auto parts store) is the most common way to seal the differential cover on a Dana 60 axle, however, several aftermarket manufacturers now offer reusable gaskets that are much cleaner.
Learn More About Differential Gaskets
Dana Spicer recommends 80w90 Mineral oil or 75W140 synthetic oil, however, we recommend 75w90 full-synthetic gear oil for all Dana 60 applications (plus a traction modifier for differentials that require it).
Learn More About Gear Oil
It is not common to need to replace a pinion yoke but in high horsepower applications, or if your driveshaft has been upgraded to larger u-joints, you may need to purchase a stronger and/or larger yoke.
Learn More About Pinion Yokes